Meter

Flat Cable for Massy Ferguson Instrument Cluster Application: Massy Ferguson Instrument Cluster Flat Cable Size: 39*23mm 36tracks Package Included: 1PCS Flat Cable

Tachometer Circuit Repair Board with LEDs for Corvette C3 1978-1982 The old circuit board that often fails completely or becomes inaccurate. Directly replace this new circuit board, to avoid the high cost of tach restoration for your 1978-1982 Corvette. The new design board may look a little differently with your original, this should not be cause for concern. Our circuit board do not use or need the red insulating washers for installation. The circuit board is print marked so it cannot be installed backwards. This tach board comes pre-calibrated, but includes fine adjustment ability if needed. Just remove your old tachometer, bolt on the new circuit board and re-install your tach. No spacers needed like on other replacements. The direction mark is printed on the circuit board, so it cannot be installed backwards. Feature: Best fit and preform better than the original! No soldering. Simply unbolt the old circuit board and bolt on the new one. All circuit boards are calibrated for a 8 Cylinder unless otherwise requested. LEDs for confirming good coil signal and power to gauge. Fast & Free Shipping to US. Lifetime Warranty! Package included: 1PCS Tachometer Circuit Repair Board with LEDs. Tachometer on picture for show scene application not included for selling.

Tachometer Circuit Repair Board for Corvette C3 1978-1982 The old circuit board that often fails completely or becomes inaccurate. Directly replace this new circuit board, to avoid the high cost of tach restoration for your 1978-1982 Corvette. The new design board may look a little differently with your original, this should not be cause for concern. Our circuit board do not use or need the red insulating washers for installation. The circuit board is print marked so it cannot be installed backwards. This tach board comes pre-calibrated, but includes fine adjustment ability if needed. Just remove your old tachometer, bolt on the new circuit board and re-install your tach. No spacers needed like on other replacements. The direction mark is printed on the circuit board, so it cannot be installed backwards. Feature: Best fit and preform better than the original! No soldering. Simply unbolt the old circuit board and bolt on the new one. All circuit boards are calibrated for a 8 Cylinder unless otherwise requested. Fast & Free Shipping to US. Lifetime Warranty! Package included: 1PCS Tachometer Circuit Repair Board Tachometer on picture for show scene application not included for selling.

7" Touch Screen Digitizer for Acura MDX TLX, Honda Odyssey Radio Stereo Compatible with the following vehicles: Acura MDX (2014-2016) Acura TLX (2015-2017) Honda Odyssey (2014-2016) The double ribbon cable screen is from OEM factory and retain screen vibrate function. We selling is single ribbon cable screen rebuild at aftermatket factory and does not support screen vibrate function. Radio Navigation Monitor OEM Number: 39540TZ3A220M1 39540TZ3A150M1 39540TZ3A140M1 39540TZ3A130M1 39540-TZ3-A220-M1 39540-TZ3-A150-M1 39540-TZ3-A140-M1 39540-TZ3-A130-M1 According to Screen OEM Number: C070VVN02 Features & Specifications: - 100% new and high quality, good operation. - Size: 7 inch (167*109mm). - Cable Interface: 4-Pin. - Thickness: 1.5mm - Length of FPC (flexible print circuit): 60mm. - Working voltage: 5V. - Main material: Glass. - TFT (LCD) technology. - Replacing touch screen: Loss of response to touch commands, scratches, cracks, dead pixels, or the polarized protection is wearing off. Attention: 1. The cable (FPC) interface of the touch screen digitizer is 4-pin. 2. Installation instructions not included. Tool not included. 3. It is only a touch panel, not including a LCD display. 4. Does not retain screen vibrate function. 5. Please check the exact dimensions of the touch screen before buying to make sure that it is fit for your device. If there is any question/problem, please feel free to contact us. 6. There is a layer of protective film on the surface of the panel. Please remove the protective film before using it. Package included: 1x Touch Screen Glass Digitizer

Touch Screen Digitizer for Toyota Prius Hybrid Sedan 2004-2009 Application: Toyota Prius Hybrid Sedan Will fit both Navigation and Non-Navigation MFD (2004-2009) OEM Number: 86110-47210, 86110-47220, 86110-47230, 86110-47081, 86110-47080, 86110-47070 If you have ordered can require us for Removal Instructions of Prius Navigation Unit. Also Applied On: Lexus GS300 GS350 GS430, GS450h (2005-2009) Lexus IS250 IS300 IS350, IS-F (2006-2009) Lexus GX GX470 Truck, Suv (2005-2009) Lexus RX300, RX330, RX350, RX400, RX400H (2004-2009) LX470 ES350 (2007-2011) Screen Part Number: LTA070B510F, LTA070B511F Features & Specifications: - High quality and good operation. - Fit for both Navigation and Non-Navigation MFD - Size: 7.3 inch (170*107mm). - Length of FPC (flexible print circuit): 50mm - Interface: 4-Pin. - Thickness: 1.8mm - Main material: Glass. - Working Voltage: 5V. - Replacing touch screen: Loss of response to touch commands, scratches, cracks, dead pixels, or the polarized protection is wearing off. Attention: 1. The cable interface of the touch screen is 4-pins. 2. Installation instructions not included. Tool not included. 3. It is only a touch panel, not including a LCD display. 4. Please check the exact dimensions of the touch screen before buying to make sure that it is fit for your device. If there is any question/problem, please feel free to contact us. 5. There is a layer of protective film on the surface of the panel. Please remove the protective film before using it. Package Included: 1PCS 7.3" Touch Screen Digitizer for Toyota Prius Hybrid Sedan 2004-2009

7" Touch Screen Digitizer for LAM070G004A Peugeot 208 2008 308 Citroen C5 C4l C 3xr Application: Peugeot 208 2008 308 Citroen C5 C4l C3xr. Replacement for SANYO LAM070G004A, SONY GCX156AKM-E, GCX156AKS-T02 and BOE A2C00730002-01. Features & Specifications: - 100% new and high quality, good operation. - Screen Size: 7.0 inch (167*104.3mm). - Interface: 4-Pin. - Thickness: 1.9mm - Length of FPC (flexible print circuit) / Ribbon cable connector: 49.2mm. - Working voltage: 5V. - Special feature: Support Can-Bus. - Main material: Glass. - TFT (LCD) technology. - Replacing touch screen: Loss of response to touch commands, scratches, cracks, dead pixels, or the polarized protection is wearing off. Attention: 1. Installation instructions not included. Tool not included. 2. It is only a touch panel, not including a LCD display. 3. Please check the exact dimensions of the touch screen before buying to make sure that it is fit for your device. If there is any question/problem, please feel free to contact us. 4. There is a layer of protective film on the surface of the panel. Please remove the protective film before using it. Package included: 1x Touch Screen Glass Digitizer

Printed Circuit Board for Ford Mustang 1969-1970 Instrument Panel Bezel W/O Tach Application: Ford Mustang Instrument (1969-1970) Behind Instrument Panel Bezel Without Factory Tachometer Version Reference OEM Numbers: C9ZF-10C956 C9ZZ-10K843-A Replace our improved quality printed circuit board for Ford Mustang gauge cluster could provide the solution to your blinking or non-functioning gauges, lamps. We re-introduces this discontinued 1969-1970 Ford Mustang gauge cluster circuit boards with thicker copper circuit paths and bulb contact points. Feature: - New! Improved quality than OEM design. Lifetime warranty! - Easy! Plug-in installation. - Thicker copper circuit paths and bulb contact points. Package included 1PCS Printed Circuit Board Ford Mustang 1969-1970 instrument panel on picture is for show of application scene which is not included for selling.

Wiring Adapter for BMW E30 E24 E28 Euro Analog Clock Original with 6 Button OBC Application: BMW E30 E24 E28 with the 6 Button/BC1 on Board Computer Unit This item fits E30 318i, 318is, 325e, 325es, 325i, 325is, 325ic. 325ix, and M3 - Model Years 1986, 1987, 1988, 1989, 1990, 1991, 1992(convertible), and 1993(convertible). BMW E30 3 Series 318i (1984-1992) BMW E30 3 Series 318is (1984-1992) BMW E30 3 Series 325e (1984-1992) BMW E30 3 Series 325es (1984-1992) BMW E30 3 Series 325i (1984-1992) BMW E30 3 Series 325is (1984-1992) BMW E30 3 Series 325iX (1984-1992) BMW E30 3 Series M3 (1988-1991) The wiring harness adapter is auto aftermarket made to allows you plug the clock into your existing dashboard harness without any modification. Quickly install your BMW analog euro clock into your E30 OBC dash panel with no wire splicing or modifications. Just plug one end into the clock and the other into the wiring harness and save yourself the time and potential issues with cutting, splicing and stressing your vintage in-dash wiring loom. Clock OEM Part No.: 1376903 62.13 Borg Package Included: 1PCS Wiring Adapter for BMW E30 E24 E28 Euro Analog Clock The analog clock only as an application scenario display, not included for sale.

Flat Cable for Citroen C5/Xsara, Peugeot 206/307 Clock Radio Info Digital Centre Display Application: Citroen C5(2001-2004) Citroen Xsara N1(1997-2005) Peugeot 206 (1998-2006) Peugeot 307 (2001-2004) Reference OEM Numbers: 9650243177/216736252/216564820 9647409677/216709375 9650242977/21673628/216592759 9640963777/21657730 9646652577/21669450 Flat Cable Size: 111*22mm 156tracks Infocenter made by Sagem Package Included: 1PCS Flat Cable Multi-function Info Center on picture for show scene application not included for selling.

Gauge Face Overlay for Mercedes W211 W209 C219 Instrument Cluster 260KM/H Black Application: Mercedes E-Class W211 E320 E350 E500 E55 E63 (2002-2009) Mercedes CLK-Class W209 (2002-2010) Mercedes CLS-Class C219 (2004-2010) Feature: Color: White Maximum Speed Scale: 260KM/H